fb2CG@KU15P FPGA Card

Dual QSFP28 port 2x100GE Xilinx® Kintex UltraScale+

The 100G Dual FPGA Card fb2CG@KU15P is a high performance OEM hardware platform intended for 10/40/25/50/100 Gigabit Ethernet via its dual QSFP28 slots.
The standard configuration is based on the Xilinx Kintex UltraScale+ KU15P FPGA, to provide ample capacity for the dual QSFP28 interface.

The card features the KU15P to keep the solution as cost effective as high performance computing allows.
The card is mounted with 4 x 72-bit DDR4 ECC RAM, 4GB for a total of 16 GB.

fb2CG@KU15P FPGA Card

Dual QSFP28 port 2x100GE Xilinx® Kintex UltraScale+

Xilinx® Kintex UltraScale+ XCKU15P FPGA
2 x QSFP28 ports
4 x 72-bit DDR4@2666MT/s (4 GB per bank with ECC)
Support for direct Card to Card interconnect with up to 150Gbit/s
Configuration flash RAM for boot images
PCIe form-factor: Full height, half length (111.15 x 167.65 mm with bracket)
On-board power and temperature sensors
FPGA controlled link and status LEDs
Active and passive cooling alternatives available

fb2CG@KU15P FPGA Card

Dual QSFP28 port 2x100GE Xilinx® Kintex UltraScale+

General Technical Specifications
Host Interface	Physical bus connector: 16-lane PCIe PCIe bus type: 1-16 lane PCIe Gen1/Gen2/Gen3 Support for SMBUS
Network Interface	IEEE standard: IEEE 802.3 10/40/25/100 GE Physical interface: 2 x QSFP28 ports Supported QSFP+/QSFP28 modules: including fan-out modules for 4x10G/4x25GE, multimode SR4 (850nm), singlemode LR4 (1310nm), multimode LRM4 (1310 nm), or direct Attached Copper (Twinax) and others. Data rate: 8×10, 2×40, 8×25, 2×100 Gbps Support for SyncE
Configuration	Quad SPI fast parallel programming interface from supporting preprogrammed controller Configuration flash supports two boot images with automatic fallback to fail safe image if first image fails Upload of FPGA configuration to flash via PCIe or directly from Xilinx Vivado via the onboard JTAG dongle Direct FPGA configuration from Xilinx via the onboard JTAG dongle Support for encrypted FPGA bit file (optional) Supports Tandem PROM boot
On-Board Memory	4 x 72-bit DDR4@2666MT/s (4 GB per bank with ECC) User configurable space in flash RAM for permanent storage Configuration flash RAM for boot images
On-Board Clock	PCIe clock: 100 MHz 2 x differential 161.13 MHz SerDes clock for Ethernet 2 x differential 161.13 MHz SerDes clock for Expansion 2 x differential 266.67 MHz clock for Memory 50 MHz clock
FPGA details	FPGA Xilinx Kintex Ultrascale+ XCKU15P
Environment	Physical dimensions: Full height, ½ length 111.15 x 167.65 mm with bracket Storage temperaure: -30 – 70°C , -22 – 158°F Operating temperature: 0 – 55°C, 30 – 130°F Operating humidity: 20 – 80% Hardware compliance: RoHS, CE
Additional Board Support	On-board power and temperature sensors FPGA controlled Link and Activity LED for each port. 4 for each QSFP. Board status LEDs Battery holder for coin cell battery for back-up of Key memory for bitstream encryption. (optional) Failsafe button on bracket PPS clock synchronization connector Support for direct Card to Card interconnect with up to 150Gbit/s
Power	Max 120W, above 75W PCIe AUX power must be used Active and passive cooling alternatives available Power, temperature and FAN tacho sensor reading PCIe AUX power connector available
On-Board Microcontroller	Board management Microcontroller for various internal control tasks as well as external communication SMbus/I2c Possible to readout telemetry parameters

fb2CG@KU15P FPGA Card

Dual QSFP28 port 2x100GE Xilinx® Kintex UltraScale+

P/N	Description
fb2CG@KU15P	Xilinx® Kintex UltraScale+ XCKU15P FPGA

Products

FPGA Based Cards

FPGA Xilinx Based

fb2CG@KU15P FPGA Card

Dual QSFP28 port 2x100GE Xilinx® Kintex UltraScale+

fb2CG@KU15P FPGA Card

Dual QSFP28 port 2x100GE Xilinx® Kintex UltraScale+

fb2CG@KU15P FPGA Card

Dual QSFP28 port 2x100GE Xilinx® Kintex UltraScale+

General Technical Specifications

fb2CG@KU15P FPGA Card

Dual QSFP28 port 2x100GE Xilinx® Kintex UltraScale+

P/N

Description

fb2CG@KU15P FPGA Card