Products

EOL Products

PEG2FI

Dual Port Fiber Gigabit Ethernet PCI Express Server Adapter Intel® Based

This product has been discontinuedEOL Notification

Silicom’s Gigabit Ethernet PCI Express Server adapters are PCI-Express Server Adapters cards that contain Multiple / Single Gigabit ports/ on a PCI-Express adapter.

Silicom’s Gigabit Ethernet PCI Express Server adapters are designed for Servers and high-end appliances. The performance is optimized so that system I/O is not the bottleneck in high-performance networking applications. Silicom’s Gigabit PCI Ethernet Cards enable fault-tolerant via teaming. Traffic from the failed port is routed through other members of the team.

Silicom’s Gigabit Ethernet PCI-Express Server adapters have an integrated hardware acceleration that performs TCP/UDP/IP checksum offload and TCP segmentation. The host processing offloads accelerators frees CPU for application processing.

Silicom’s Gigabit Ethernet PCI-Express Server adapters are the ideal solution for implementing multiple network segments, mission-critical high-powered networking applications and environments within high performance servers.

PEG2FI

Dual Port Fiber Gigabit Ethernet PCI Express Server Adapter Intel® Based

Fiber Gigabit Ethernet 1000Base-SX:

  • Independent Fiber Gigabit Ethernet channels support Gigabit Ethernet 1000Base-SX
  • Small Form Factor (SFF) LC Connectors
  • 2PortLink synchronization

Fiber Gigabit Ethernet 1000Base-LX:

  • Independent Fiber Gigabit Ethernet channels support Gigabit Ethernet 1000Base-LX
  • Small Form Factor (SFF) LC Connectors
  • 2PortLink synchronization

Common Key Features:

  • Host Interface:
  • Host Interface standard support:
  • PCI-Express Base Specification Revision 1.0a.
  • High performance, reliability, and low power use in advanced Intel integrated MAC + PHY / SERDES chip Controllers
  • Ultra deep, packet buffer per channel lowers CPU utilization, avoids PCI-Express congestion
  • Hardware acceleration that can offload tasks from the host processor. The Controllers can offload TCP/UDP/IP checksum calculations and TCP segmentation
  • Server class reliability, availability and performance features:
  • Link Aggregation and Load Balancing
    • Switch dependent: 802.3ad (LACP), Generic Trunking ( GEC / FEC)
    • Switch and NIC Independent
    • Failover
  • Priority queuing – 802.1p layer 2 priority encoding
  • Virtual LANs –802.1q VLAN tagging
  • Jumbo Frame (16KB)
  • 802.x flow control
  • Statistics for SNMP MIB II, Ethernet like MIB, and Ethernet MIB (802.3z, Clause 30)
  • LEDs indicators for link/Activity/Speed status

PEG2FI

Dual Port Fiber Gigabit Ethernet PCI Express Server Adapter Intel® Based

Fiber Gigabit Ethernet Technical Specifications – (1000Base-SX) Adapters:

IEEE Standard / Network topology: Fiber Gigabit Ethernet, 1000Base-SX (850nM)
Data Transfer Rate: 2000Mb/s in full duplex mode per port
Cables and Operating distance: Multimode fiber:
220m at 62.5 um
550m at 50 um
Optical Output Power: Typical: -6 dBm
Minimum: -9.5 dBm
Optical Receive Sensitivity: Typical: -21 dBm
Maximum: -17 dBm

Fiber Gigabit Ethernet Technical Specifications – (1000Base-LX) Adapters:

IEEE Standard / Network topology: Fiber Gigabit Ethernet, 1000Base-LX (1310nM)
Data Transfer Rate: 2000Mb/s in full duplex mode per port
Cables and Operating distance: Single-Mode: 5000m at 9um
Multimode fiber: 550m at 50 um
550m at 62.5 um
Optical Output Power: Typical: -6 dBm
Minimum: -10 dB dBm
Optical Receive Sensitivity: Typical: -25 dBm
Maximum: -20 dBm

Operating Systems Support

Operating system support: Windows
Netware
Linux
FreeBSD
Unix
Solaris X86
VMware

General Technical Specifications

Interface Standard: PCI-Express Base Specification Revision 1.0a
Board Size: Low profile short add-in card: 167.64mm X 68.91mm (6.60”X 2.713”)
PCI Express Card Type: X4 Lane
PCI Express Voltage: +3.3V +-9%
PCI Connector: X4 Lane
Controller:  Intel 82571EB
Holder: Metal Bracket
Weight: 90 gram (3.17 Oz)
Power Consumption: PEG2Fi-SX
3.2W: 0.96A at 3.3V, Typical all ports operate at 1000Mb/s.
3.2W: 0.96A at 3.3V,Typical No link at all ports
PEG2Fi-lX
3.4W: 1.03A at 3.3V: Typical all ports operate at 1000Mb/s.
3.5Wl: 1.06A at 3.3V: Typical No link at all ports
Operating Humidity: 0%–90%, non-condensing
Operating Temperature: 0°C – 50°C (32°F – 122°F)
Storage: -20°C–65°C (-4°F–149°F)
EMC Certifications: FCC Part 15, Subpart B Class B
Conducted Emissions
Radiated Emissions
CE EN 55022: 1998 Class B Amendments A1: 2000; A2: 2003
Conducted Emissions
Radiated Emissions
CE EN 55024: 1998 Amendments A1: 2000; A2: 2003
Immunity for ITE Amendment A1: 2001
CE EN 61000-3-2 2000, Class A
Harmonic Current Emissions
CE EN 61000 3-3 1995, Amendment A1: 2001
Voltage Fluctuations and Flicker
CE IEC 6100-4-2: 1995
ESD Air Discharge 8kV. Contact Discharge 4kV.
CE IEC 6100-4-3:1995
Radiated Immunity (80-1000Mhz), 3V/m 80% A.M. by 1kHz
CE IEC 6100-4-4:1995
EFT/B: Immunity to electrical fast transients 1kV Power
Leads, 0.5Kv Signals Leads
CE IEC 6100-4-5:1995
Immunity to conductive surges COM Mode; 2kV,
Dif. Mode 1kV
CE IEC 6100-4-6:1996
Conducted immunity (0.15-80 MHz) 3VRMS 80% A.M.
By 1kHz
CE IEC 6100-4-11:1994
Voltage Dips and Short Interruptions
V reduc >95%, 30% >95% Duration 0.5per, 25per, 250per
MTBF*: 143 (Years)
*According to Telcordia SR-332 Issue 1
Environmental condition – GB (Ground, Fixed, Controlled). Ambient temperature – 25°C. Temperature rise of 10°C above the system ambient temperature was assumed for the cards components

LEDs

LEDs: (2) LEDs per port
Link: Turns on Fiber link (green)
Act: Blinks on activity (green)
LEDs location: LEDs are located on the PCB, visible via holes in the metal bracket holder
Connectors: LC Connectors

PEG2FI

Dual Port Fiber Gigabit Ethernet PCI Express Server Adapter Intel® Based

P/N

Description

Notes

PEG2FI-RoHS Dual Port Fiber (SX) Gigabit Ethernet PCI Express Server Adapter X4, Based on 82571
PEG2FI-LX- RoHS Dual port Fiber (LX) Gigabit Ethernet PCI Express Server Adapter X4, Based on 82571

 

Model P/N -LP / -RoHS

-RoHS: RoHS Compliant / Lead free adapter.

-LP: Assemble Low Profile Metal Bracket, available in dual or single port only

2V1